This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
todo [2019/10/19 19:17] sdh7 |
todo [2019/10/22 19:09] (current) sdh7 |
||
---|---|---|---|
Line 11: | Line 11: | ||
* <del>the i3 needs its BuildTak replaced. We have it, just need to do it...</del> | * <del>the i3 needs its BuildTak replaced. We have it, just need to do it...</del> | ||
* <del>Deep cleaning & organizing at the Electronics Station</del> | * <del>Deep cleaning & organizing at the Electronics Station</del> | ||
- | * Take apart the Hot air station and see if the pump can be repaired or replaced. | ||
* <del>Paint Marker an "MA" on tools that don't have it, so that they're easier to identify</del> | * <del>Paint Marker an "MA" on tools that don't have it, so that they're easier to identify</del> | ||
- | * Reorganize green tool shelf - re-optimize cubbies to make more sense | + | * <del>Reorganize green tool shelf - re-optimize cubbies to make more sense</del> |
* <del>Set aside two cubbies for measuring tools</del> | * <del>Set aside two cubbies for measuring tools</del> | ||
* <del>Re-label new cubbies by use</del> | * <del>Re-label new cubbies by use</del> | ||
- | * Finding things: | + | * <del>Finding things:</del> |
* <del>The bin of USB Micro/C/Lightning cables</del> | * <del>The bin of USB Micro/C/Lightning cables</del> | ||
* <del>The Ryobi Multitool body - we have a head for it now, but the body is AWOL</del> | * <del>The Ryobi Multitool body - we have a head for it now, but the body is AWOL</del> | ||
* <del>Pen turning stock</del> | * <del>Pen turning stock</del> | ||
+ | * <del>Chain & combination lock</del> | ||
* <del>Go through the Pallet Racks a little bit - clean up/consolidate where possible</del> | * <del>Go through the Pallet Racks a little bit - clean up/consolidate where possible</del> | ||
* <del>Assuming some space is freed up here, move some extraneous things into it as "deep storage" (i.e. all but one of the totes of "wire bundles", etc.)</del> | * <del>Assuming some space is freed up here, move some extraneous things into it as "deep storage" (i.e. all but one of the totes of "wire bundles", etc.)</del> | ||
- | * A general going-through of the shelves: | + | * <del>A general going-through of the shelves:</del> |
- | * Consolidate things that need to be consolidated | + | * <del>Consolidate things that need to be consolidated</del> |
- | * Purge things that need to be purged | + | * <del>Purge things that need to be purged</del> |
- | * label things that need to be labeled | + | * <del>label things that need to be labeled</del> |
* Label cabinets in the Shop Zone based on what's inside each door | * Label cabinets in the Shop Zone based on what's inside each door | ||
* disc/strip sander needs a new sanding belt (1x30?) - belts purchased, just need to install... | * disc/strip sander needs a new sanding belt (1x30?) - belts purchased, just need to install... | ||
+ | * Turns out it's 1x42". Ross may have some, or we can order more. | ||
* Build a little stand for the [[Monoprice SLA Printer]], such that the [[UV Curing Lamp]] sits under it (with a little extra space for curing taller parts. | * Build a little stand for the [[Monoprice SLA Printer]], such that the [[UV Curing Lamp]] sits under it (with a little extra space for curing taller parts. | ||
* Bonus - add a translucent acrylic window on hinges to cover the lamp area - the laser cutter should be able to handle that size... | * Bonus - add a translucent acrylic window on hinges to cover the lamp area - the laser cutter should be able to handle that size... | ||
* <del>Double bonus - fix the SLA printer vat...</del> | * <del>Double bonus - fix the SLA printer vat...</del> | ||
+ | * <del>Take apart the Hot air station and see if the pump can be repaired or replaced.</del> | ||
+ | * <del>Good news - pump does work if "AIR" pot is turned all the way up. Errant pot looks like a 500k...</del> | ||
| | ||
Line 52: | Line 55: | ||
* Electrical wiring for the "new" 220V stick welder (convert its plug to something better? L6-30? - check with John K.?) | * Electrical wiring for the "new" 220V stick welder (convert its plug to something better? L6-30? - check with John K.?) | ||
* Build a nice table add-on/fence for the [[Enco Drill Press]]? | * Build a nice table add-on/fence for the [[Enco Drill Press]]? | ||
- | * Measure T-slot nuts for the [[Enco Drill Press]]. See of additional ones are available, or maybe make some. | + | * <del>Measure T-slot nuts for the [[Enco Drill Press]]. See of additional ones are available, or maybe make some.</del> |
* Implement Dust Collection Station? | * Implement Dust Collection Station? | ||