todo
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
todo [2019/10/08 16:29] – sdh7 | todo [2019/10/18 14:52] – [Next Makerspace Maintenance Punch List **(10/19)**] sdh7 | ||
---|---|---|---|
Line 4: | Line 4: | ||
* IEC power cables? Our stash is getting a little low... | * IEC power cables? Our stash is getting a little low... | ||
- | ====Next Makerspace Maintenance Punch List==== | + | ====Next Makerspace Maintenance Punch List **(10/19)**==== |
+ | * Clear off main two tables, and refresh the paper tops | ||
+ | * Take garbage to dumpster | ||
+ | * Improved shelving around the back of the space? - we have some pieces of 2x10 that might be useful for this... | ||
+ | * Re-work back wall in general - move speakers to corners for better separation(? | ||
* Build a little stand for the [[Monoprice SLA Printer]], such that the [[UV Curing Lamp]] sits under it (with a little extra space for curing taller parts. | * Build a little stand for the [[Monoprice SLA Printer]], such that the [[UV Curing Lamp]] sits under it (with a little extra space for curing taller parts. | ||
* Bonus - add a translucent acrylic window on hinges to cover the lamp area - the laser cutter should be able to handle that size... | * Bonus - add a translucent acrylic window on hinges to cover the lamp area - the laser cutter should be able to handle that size... | ||
- | | + | |
+ | * <del>the i3 needs its BuildTak replaced. We have it, just need to do it...</ | ||
+ | * Deep cleaning & organizing at the Electronics Station | ||
+ | * Take apart the Hot air station and see if the pump can be repaired or replaced. | ||
+ | * Finding things: | ||
+ | * The bin of USB Micro/ | ||
+ | * The Ryobi Multitool body | ||
+ | * Label cabinets in the Shop Zone based on what's inside each door | ||
+ | * disc/strip sander needs a new sanding belt (1x30?) - belts purchased, just need to install... | ||
* Go through the Pallet Racks a little bit - clean up/ | * Go through the Pallet Racks a little bit - clean up/ | ||
* A general going-through of the shelves: | * A general going-through of the shelves: | ||
* Consolidate things that need to be consolidated | * Consolidate things that need to be consolidated | ||
* Purge things that need to be purged | * Purge things that need to be purged | ||
+ | * label things that need to be labeled | ||
| | ||
====General Space Infrastructure==== | ====General Space Infrastructure==== | ||
Line 28: | Line 41: | ||
====Shop Zone==== | ====Shop Zone==== | ||
+ | |||
* Tool organization - any improvements are welcome! | * Tool organization - any improvements are welcome! | ||
* Electrical wiring for the " | * Electrical wiring for the " | ||
Line 56: | Line 70: | ||
* Make some kind of filament storage solution? (clear plastic tote w/holes & gaskets, and a bunch of color-changing silica gel??) | * Make some kind of filament storage solution? (clear plastic tote w/holes & gaskets, and a bunch of color-changing silica gel??) | ||
* Figure out steps needed to make the [[K40 Laser Engraver]] chooch safely & reasonably | * Figure out steps needed to make the [[K40 Laser Engraver]] chooch safely & reasonably | ||
+ | * Move the surge strip powering that stuff to the front of the cart. | ||
* Add an Emergency stop? | * Add an Emergency stop? | ||
* Figure out water pump/alarm stuff (short version: water pump is running, but flow alarm is triggering? need better pump? replace alarm? right now alarm is shorted out in order to test functionality...) | * Figure out water pump/alarm stuff (short version: water pump is running, but flow alarm is triggering? need better pump? replace alarm? right now alarm is shorted out in order to test functionality...) | ||
- | * Add air assist | + | * <del>Add air assist</ |
====Electronics==== | ====Electronics==== |
todo.txt · Last modified: 2019/10/22 23:09 by sdh7