todo
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
todo [2019/07/21 01:53] – sdh7 | todo [2019/10/16 13:56] – sdh7 | ||
---|---|---|---|
Line 2: | Line 2: | ||
====THINGS YOU CAN BRING THAT WOULD HELP==== | ====THINGS YOU CAN BRING THAT WOULD HELP==== | ||
* < | * < | ||
- | * < | ||
* IEC power cables? Our stash is getting a little low... | * IEC power cables? Our stash is getting a little low... | ||
- | ====7/20 Punch List==== | + | ====Next Makerspace Maintenance |
- | * < | + | |
* Build a little stand for the [[Monoprice SLA Printer]], such that the [[UV Curing Lamp]] sits under it (with a little extra space for curing taller parts. | * Build a little stand for the [[Monoprice SLA Printer]], such that the [[UV Curing Lamp]] sits under it (with a little extra space for curing taller parts. | ||
* Bonus - add a translucent acrylic window on hinges to cover the lamp area - the laser cutter should be able to handle that size... | * Bonus - add a translucent acrylic window on hinges to cover the lamp area - the laser cutter should be able to handle that size... | ||
- | | + | * < |
- | * improved under-bench storage? | + | * < |
- | * < | + | * Take apart the Hot air station and see if the pump can be repaired or replaced. |
+ | * Label cabinets in the Shop Zone based on what's inside each door | ||
+ | * disc/strip sander needs a new sanding belt (1x30?) - belts purchased, just need to install... | ||
+ | | ||
+ | * Re-work back wall in general - move speakers for better separation(? | ||
* Go through the Pallet Racks a little bit - clean up/ | * Go through the Pallet Racks a little bit - clean up/ | ||
- | * < | ||
- | * Vinyl cutter still gets kind of a raw deal in this (store it sideways), but it's an improvement... | ||
- | * Put up a bit of pegboard behind laser cutter? | ||
- | * Put a shelf above the pegboard, for storing vinyl cutter tools/laser stock, and a light underneath? | ||
* A general going-through of the shelves: | * A general going-through of the shelves: | ||
* Consolidate things that need to be consolidated | * Consolidate things that need to be consolidated | ||
- | * Purge things that need to be purged | + | * Purge things that need to be purged |
- | * < | + | * label things that need to be labeled |
- | * This has been started already | + | |
- | * Laser cutter air assist - a nozzle attachment has been printed, should just be plumbing some tubing to the pump | + | |
- | * Add light switch to activate air assist if we wanna get fancy. | + | |
| | ||
====General Space Infrastructure==== | ====General Space Infrastructure==== | ||
Line 40: | Line 35: | ||
====Shop Zone==== | ====Shop Zone==== | ||
- | * Drill bit sorting(ok, probably not, but it does drive me crazy) | + | |
- | * Priority: really low, unless it's driving you crazier than me. | + | |
* Tool organization - any improvements are welcome! | * Tool organization - any improvements are welcome! | ||
- | * Better stand/mount for the [[Disc Sander]]? If not, see about improving stiffness of the existing stand... | ||
* Electrical wiring for the " | * Electrical wiring for the " | ||
* Build a nice table add-on/ | * Build a nice table add-on/ | ||
Line 71: | Line 64: | ||
* Make some kind of filament storage solution? (clear plastic tote w/holes & gaskets, and a bunch of color-changing silica gel??) | * Make some kind of filament storage solution? (clear plastic tote w/holes & gaskets, and a bunch of color-changing silica gel??) | ||
* Figure out steps needed to make the [[K40 Laser Engraver]] chooch safely & reasonably | * Figure out steps needed to make the [[K40 Laser Engraver]] chooch safely & reasonably | ||
+ | * Move the surge strip powering that stuff to the front of the cart. | ||
* Add an Emergency stop? | * Add an Emergency stop? | ||
* Figure out water pump/alarm stuff (short version: water pump is running, but flow alarm is triggering? need better pump? replace alarm? right now alarm is shorted out in order to test functionality...) | * Figure out water pump/alarm stuff (short version: water pump is running, but flow alarm is triggering? need better pump? replace alarm? right now alarm is shorted out in order to test functionality...) | ||
- | * Add air assist | + | * <del>Add air assist</ |
====Electronics==== | ====Electronics==== | ||
* Organize components better? | * Organize components better? | ||
- | * < | ||
* Organize electronics tools better - electronics bench is a good start at this... | * Organize electronics tools better - electronics bench is a good start at this... | ||
* < | * < | ||
Line 96: | Line 89: | ||
====Miscellaneous==== | ====Miscellaneous==== | ||
* Inventory First Aid supplies. Make list of recommended additions and/or replacements for anything missing. | * Inventory First Aid supplies. Make list of recommended additions and/or replacements for anything missing. | ||
+ | * There are OSHA guidelines for what should be in one for various group sizes. | ||
* Repair the rolling cart - I kind of tried epoxy but it didn't seem to work. Weld? Bolt? | * Repair the rolling cart - I kind of tried epoxy but it didn't seem to work. Weld? Bolt? | ||
todo.txt · Last modified: 2019/10/22 23:09 by sdh7