todo
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
todo [2018/03/09 12:30] – sdh7 | todo [2018/08/07 11:37] – sdh7 | ||
---|---|---|---|
Line 13: | Line 13: | ||
* LABEL BOXES/ | * LABEL BOXES/ | ||
* literally work on anything on the [[fixme list]] | * literally work on anything on the [[fixme list]] | ||
- | * Reorganize sign in table so stuff doesn' | ||
* Use the new [[Vinyl Cutter]] to make a magnetic sign for the outside door. | * Use the new [[Vinyl Cutter]] to make a magnetic sign for the outside door. | ||
====Shop Zone==== | ====Shop Zone==== | ||
- | * Continue repairs on the [[Shopsmith Mark V]]. | + | |
- | * Solve Leak in the [[Sand Blaster]] or get a new one. | + | |
+ | * Move [[Shop Press]] back into the workshop area | ||
+ | * Start working on the new-to-us band saw from Akron Makerspace | ||
+ | * Figure out all the stuff it needs done to make it a viable tool | ||
+ | * Needs a new power cord. | ||
+ | * Blade is insanely rusty, but does move freely | ||
* Drill bit sorting(ok, probably not, but it does drive me crazy) | * Drill bit sorting(ok, probably not, but it does drive me crazy) | ||
* Priority: really low, unless it's driving you crazier than me. | * Priority: really low, unless it's driving you crazier than me. | ||
Line 25: | Line 29: | ||
* Better stand/mount for the [[Disc Sander]]? | * Better stand/mount for the [[Disc Sander]]? | ||
* Better organization inside the gray bench cabinets in general | * Better organization inside the gray bench cabinets in general | ||
- | * Electrical wiring for the " | + | * Electrical wiring for the " |
- | * < | + | * Put the [[Enco Drill Press]] back together |
- | * Move the yellow folding welding tables up onto the Pallet racks - they' | + | |
* Build a nice fence for the [[Enco Drill Press]] | * Build a nice fence for the [[Enco Drill Press]] | ||
* Measure T-slot nuts for the [[Enco Drill Press]]. See of additional ones are available, or maybe make some. | * Measure T-slot nuts for the [[Enco Drill Press]]. See of additional ones are available, or maybe make some. | ||
* Finish implementing Dust Collection Station. | * Finish implementing Dust Collection Station. | ||
- | * Move the really big clamps off of the green tool shelf shelves. Either attach a mount to the sides or maybe the wall behind the press. | + | * <del>Move the really big clamps off of the green tool shelf shelves. Either attach a mount to the sides or maybe the wall behind the press</ |
====Electronics/ | ====Electronics/ | ||
Line 43: | Line 46: | ||
* Other software? | * Other software? | ||
* Maybe first get all of these installers onto a USB stick, so they can be done all at once. | * Maybe first get all of these installers onto a USB stick, so they can be done all at once. | ||
- | * Investigate box on the wall where an additional outlet //could// potentially go. | ||
====Computers/ | ====Computers/ | ||
- | * DesignJet printer really needs a dust cover, since it gets completely clogged up with dust and debris when not in use. | + | * <del>DesignJet printer really needs a dust cover, since it gets completely clogged up with dust and debris when not in use.</ |
- | * Figure out issue with Shapeoko spindle enable - Problem with the Arduino? Wiring? Relay Box? | + | |
* Complete [[RepRap Snappy]] | * Complete [[RepRap Snappy]] | ||
====Electronics==== | ====Electronics==== | ||
- | * Organize components better | + | * Organize components better? |
- | * Organize electronics tools better | + | * Organize electronics tools better |
- | * Some little plastic bins would be helpful for this (one for solder, one for desoldering tools, etc.) | + | * <del>Figure out power supply pinout for prototyping station</ |
- | * This has been started. Need more bins. | + | |
- | * Figure out power supply pinout for prototyping station. Fabricobble a replacement or otherwise find one. | + | |
====AV Stuff==== | ====AV Stuff==== | ||
Line 71: | Line 70: | ||
====Miscellaneous==== | ====Miscellaneous==== | ||
* Inventory First Aid supplies. Make list of recommended additions and/or replacements for anything missing. | * Inventory First Aid supplies. Make list of recommended additions and/or replacements for anything missing. | ||
+ | * Repair the rolling cart - I kind of tried epoxy but it didn't seem to work. Weld? | ||
====Long Term/Not any time soon==== | ====Long Term/Not any time soon==== |
todo.txt · Last modified: 2019/10/22 19:09 by sdh7