todo
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
| todo [2018/03/09 12:30] – sdh7 | todo [2018/06/30 19:28] – sdh7 | ||
|---|---|---|---|
| Line 17: | Line 17: | ||
| ====Shop Zone==== | ====Shop Zone==== | ||
| - | * Continue repairs on the [[Shopsmith Mark V]]. | + | |
| - | * Solve Leak in the [[Sand Blaster]] or get a new one. | + | |
| + | * Move [[Shop Press]] back into the workshop area | ||
| + | * Start working on the new-to-us band saw from Akron Makerspace | ||
| + | * Figure out all the stuff it needs done to make it a viable tool | ||
| + | * Needs a new power cord. | ||
| + | * Blade is insanely rusty, but does move freely | ||
| * Drill bit sorting(ok, probably not, but it does drive me crazy) | * Drill bit sorting(ok, probably not, but it does drive me crazy) | ||
| * Priority: really low, unless it's driving you crazier than me. | * Priority: really low, unless it's driving you crazier than me. | ||
| Line 25: | Line 30: | ||
| * Better stand/mount for the [[Disc Sander]]? | * Better stand/mount for the [[Disc Sander]]? | ||
| * Better organization inside the gray bench cabinets in general | * Better organization inside the gray bench cabinets in general | ||
| - | * Electrical wiring for the " | + | * Electrical wiring for the " |
| - | * < | + | |
| - | * Move the yellow folding welding tables up onto the Pallet racks - they' | + | |
| * Build a nice fence for the [[Enco Drill Press]] | * Build a nice fence for the [[Enco Drill Press]] | ||
| * Measure T-slot nuts for the [[Enco Drill Press]]. See of additional ones are available, or maybe make some. | * Measure T-slot nuts for the [[Enco Drill Press]]. See of additional ones are available, or maybe make some. | ||
| * Finish implementing Dust Collection Station. | * Finish implementing Dust Collection Station. | ||
| - | * Move the really big clamps off of the green tool shelf shelves. Either attach a mount to the sides or maybe the wall behind the press. | + | * <del>Move the really big clamps off of the green tool shelf shelves. Either attach a mount to the sides or maybe the wall behind the press</ |
| ====Electronics/ | ====Electronics/ | ||
| Line 47: | Line 50: | ||
| ====Computers/ | ====Computers/ | ||
| * DesignJet printer really needs a dust cover, since it gets completely clogged up with dust and debris when not in use. | * DesignJet printer really needs a dust cover, since it gets completely clogged up with dust and debris when not in use. | ||
| - | * Figure out issue with Shapeoko spindle enable - Problem with the Arduino? Wiring? Relay Box? | ||
| * Complete [[RepRap Snappy]] | * Complete [[RepRap Snappy]] | ||
| Line 53: | Line 55: | ||
| * Organize components better | * Organize components better | ||
| * Organize electronics tools better | * Organize electronics tools better | ||
| - | * Some little plastic bins would be helpful for this (one for solder, one for desoldering tools, etc.) | ||
| - | * This has been started. Need more bins. | ||
| * Figure out power supply pinout for prototyping station. Fabricobble a replacement or otherwise find one. | * Figure out power supply pinout for prototyping station. Fabricobble a replacement or otherwise find one. | ||
todo.txt · Last modified: 2019/10/22 19:09 by sdh7